-- *****************************************************************
-- CISCO-L2L3-INTERFACE-CONFIG-MIB -
-- configuration of switchport mode for interfaces
--
-- February 2000, Cliff Sojourner
--
-- Copyright (c) 2000 by cisco Systems, Inc.
-- All rights reserved.
-- *****************************************************************
--CISCO-L2L3-INTERFACE-CONFIG-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPEFROM SNMPv2-SMI
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
TEXTUAL-CONVENTIONFROM SNMPv2-TC
ifIndex
FROM IF-MIB
ciscoMgmt
FROM CISCO-SMI
;ciscoL2L3IfConfigMIB MODULE-IDENTITYLAST-UPDATED"200005101900Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO
"Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-snmp@cisco.com"DESCRIPTION"Interface switchport mode configuration management MIB.
This MIB is used to monitor and control
configuration of interface switchport and routed mode."REVISION"200005101900Z"DESCRIPTION"Initial version of this MIB module."::={ ciscoMgmt 151}ciscoL2L3IfConfigMIBObjects OBJECTIDENTIFIER::={ ciscoL2L3IfConfigMIB 1}cL2L3IfConfig OBJECTIDENTIFIER::={ ciscoL2L3IfConfigMIBObjects 1}--
-- Textual Conventions
--CL2L3InterfaceMode ::=TEXTUAL-CONVENTIONSTATUScurrent
DESCRIPTION"The operational mode of the interface.
For administrative and operational states, valid values are:
routed(1), switchport(2).
routed(1): Routed mode interfaces direct traffic using
layer 3 protocols.
switchport(2): Switchport-mode interfaces direct traffic using
layer 2 protocols. A switchport-mode interface can be in
access mode, or trunk mode, or multi-mode.
Switchport interface operating mode can be configured manually,
or negotiated by Dynamic Trunking Protocol (DTP) or Dynamic
Inter-Switch Link (DISL).
Access-mode interfaces carry one VLAN's traffic. Access-mode
interface parameters are configured in CISCO-VLAN-MEMBERSHIP-MIB.
Trunk-mode interfaces carry one or more VLANs. VLAN-related
trunk-mode interface parameters are configured in CISCO-VTP-MIB.
Multi-mode interfaces carry one VLAN to each alias of a
single connected end-station. VLAN-related multi-mode
interface parameters are configured in CISCO-VTP-MIB.
"SYNTAXINTEGER{ routed(1), switchport(2)}
--
-- switchport interface mode configuration table
--cL2L3IfTable OBJECT-TYPESYNTAXSEQUENCEOF CL2L3IfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"The table shows the administratively requested and
actual operating configuration for switchport interfaces."::={ cL2L3IfConfig 1}cL2L3IfEntry OBJECT-TYPESYNTAX CL2L3IfEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry represents the configuration and operation of a
switchport interface.
Entries are created and deleted automatically in tandem
with the corresponding ifEntries."INDEX{ ifIndex }
::={ cL2L3IfTable 1}
CL2L3IfEntry ::=SEQUENCE{
cL2L3IfModeAdmin CL2L3InterfaceMode,
cL2L3IfModeOper CL2L3InterfaceMode
}cL2L3IfModeAdmin OBJECT-TYPESYNTAX CL2L3InterfaceMode
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The administratively desired interface mode."::={ cL2L3IfEntry 1}cL2L3IfModeOper OBJECT-TYPESYNTAX CL2L3InterfaceMode
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"The operational interface mode."::={ cL2L3IfEntry 2}--
-- Notifications
---- ciscoL2L3IfConfigMIBNotificationPrefix OBJECT IDENTIFIER ::=
-- { ciscoL2L3IfConfigMIB 2 }
-- ciscoL2L3IfConfigMIBNotifications OBJECT IDENTIFIER ::=
-- { ciscoL2L3IfConfigMIBNotificationPrefix 0 }--
-- Conformance
--ciscoL2L3IfConfigMIBConformance OBJECTIDENTIFIER::={ ciscoL2L3IfConfigMIB 3}ciscoL2L3IfConfigMIBCompliances OBJECTIDENTIFIER::={ ciscoL2L3IfConfigMIBConformance 1}ciscoL2L3IfConfigMIBGroups OBJECTIDENTIFIER::={ ciscoL2L3IfConfigMIBConformance 2}ciscoL2L3IfConfigMIBCompliance MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for entities which implement
the Cisco L2L3 Interface Configuration Management MIB"MODULE-- this module
MANDATORY-GROUPS{ ciscoL2L3IfConfigMIBGroup }::={ ciscoL2L3IfConfigMIBCompliances 1}--
-- Units of Conformance
--ciscoL2L3IfConfigMIBGroup OBJECT-GROUPOBJECTS{
cL2L3IfModeAdmin,
cL2L3IfModeOper
}STATUScurrentDESCRIPTION"Interface L2 & L3 mode objects"::={ ciscoL2L3IfConfigMIBGroups 1}END